¡GoConqr estrena diseño! Cuéntanos qué te parece.

Regístrate gratis

Test

Pepinillo 3

TER 86 preguntas

Hacer el test

Preguntas del test (86)

  1. 1Refer to the exhibit. Given the output for this command, if the router ID has not been manually set, what router ID will OSPF use for this router?

    RouterD# show ip interface brief

    Interface IP-Address OK? Method Status Protocol
    FastEthernet0/0 192.168.5.3 Yes manual up up
    FastEthernet0/1 10.1.1.2 Yes manual up up
    Loopback0 172.16.5.1 Yes NVRAM up up
    Loopback1 10.154.154.1 Yes NVRAM up up
    1. A10.1.1.2
    2. B10.154.154.1
    3. C172.16.5.1
    4. D192.168.5.3
  2. 2Refer to the exhibit. When running EIGRP, what is required for RouterA to exchange routing updates with RouterC?Imagen de la pregunta 2
    1. AAS numbers must be changed to match on all the routers
    2. BLoopback interfaces must be configured so a DR is elected
    3. CThe no auto-summary command is needed on Router A and Router C
    4. DRouter B needs to have two network statements, one for each connected network
  3. 3A network administrator is troubleshooting the OSPF configuration of routers R1 and R2. The routers cannot establish an adjacency relationship on their common Ethernet link.

    R1: Ethernet0 is up, line protocol is up
    Internet address 192.168.1.2/24, Area 0
    Process ID 1, Router ID 192.168.31.33, Network Type BROADCAST, Cost: 10
    Transmit Delay is 1 sec, State DR, Priority 1
    Designated Router (ID) 192.168.31.33, Interface address 192.168.1.2
    No backup designated router on this network
    Timer intervals configured, Hello 5, Dead 20, Wait 20, Retransmit 5


    R2: Ethernet0 is up, line protocol is up
    Internet address 192.168.1.1/24, Area 0
    Process ID 2, Router ID 192.168.31.11, Network Type BROADCAST, Cost: 10
    Transmit Delay is 1 sec, State DR, Priority 1
    Designated Router (ID) 192.168.31.11, Interface address 192.168.1.1
    No backup designated router on this network
    Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5

    The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2. Based on the information in the graphic, what is the cause of this problem?
    1. AThe OSPF area is not configured properly.
    2. BThe priority on R1 should be set higher.
    3. CThe cost on R1 should be set higher.
    4. DThe hello and dead timers are not configured properly.
    5. EA backup designated router needs to be added to the network.
    6. FThe OSPF process ID numbers must match.
  4. 4Refer to the exhibit. Which two statements are true about the loopback address that is configured on RouterB? (Choose two.)Imagen de la pregunta 4
    1. AIt ensures that data will be forwarded by RouterB.
    2. BIt provides stability for the OSPF process on RouterB.
    3. CIt specifies that the router ID for RouterB should be 10.0.0.1.
    4. DIt decreases the metric for routes that are advertised from RouterB.
    5. EIt indicates that RouterB should be elected the DR for the LAN.
  5. 5If all OSPF routers in a single area are configured with the same priority value, what value does a router use for the OSPF router ID in the absence of a loopback interface?
    1. Athe IP address of the first Fast Ethernet interface
    2. Bthe IP address of the console management interface
    3. Cthe highest IP address among its active interfaces
    4. Dthe lowest IP address among its active interfaces
    5. Ethe priority value until a loopback interface is configured
  6. 6The OSPF Hello protocol performs which of the following tasks? (Choose two.)
    1. AIt provides dynamic neighbor discovery.
    2. BIt detects unreachable neighbors in 90 second intervals.
    3. CIt maintains neighbor relationships.
    4. DIt negotiates correctness parameters between neighboring interfaces.
    5. EIt uses timers to elect the router with the fastest links as the designated router.
    6. FIt broadcasts hello packets throughout the internetwork to discover all routers that are running OSPF.
  7. 7What are two requirements for an HSRP group? (Choose two.)
    1. Aexactly one active router
    2. Bone or more standby routers
    3. Cone or more backup virtual routers
    4. Dexactly one standby active router
    5. Eexactly one backup virtual router
  8. 8Which two pieces of information can you learn by viewing the routing table? (Choose two.)
    1. Awhether an ACL was applied inbound or outbound to an interface
    2. Bthe EIGRP or BGP autonomous system
    3. Cwhether the administrative distance was manually or dynamically configured
    4. Dwhich neighbor adjacencies are established
    5. Ethe length of time that a route has been known
  9. 9Refer to the exhibit. Which route type does the routing protocol Code D represent in the output?

    10.0.0.0/24 is subnetted, 1 subnets
    C 10.0.0.0 is directly connected, FastEthernet0/1
    C 172.160.0/16 is directly connected, FastEthernet0/0
    D 192.168.0/24 [90/30720] via 172.16.0.2, 00:00:03, FastEthernet0/0
    1. Astatically assigned route
    2. Broute learned through EIGRP
    3. C724 route of a locally configured IP
    4. Dinternal BGP route
  10. 10An engineer must configure an OSPF neighbor relationship between router R1 and R3. The authentication configuration has been configured and the connecting interfaces are in the same192.168.1.0/30 subnet. What are the next two steps to complete the configuration? (Choose two.)
    1. Aconfigure the interfaces as OSPF active on both sides
    2. Bconfigure both interfaces with the same area ID
    3. Cconfigure the hello and dead timers to match on both sides
    4. Dconfigure the same process ID for the router OSPF process
    5. Econfigure the same router ID on both routing processes

Información

Descripción
Test sobre Pepinillo 3, creado por TER TER el 26/08/2026.
Autor
TER TER
Idioma
Español
Visitas
1
Valoración
Aún sin valoraciones
Valora este test
Valora este test

Más sobre Dynamic Routing and Protocol Types

Escríbenos

¿Sobre qué es tu mensaje?

¿Qué te parece el nuevo diseño?

¿Te gusta?