Notas
shape and space 2
Conteúdo das notas (1)
Página 1
Special Quadrilaterals
Bookmark this page
A general quad
lateral has four sides and the sum of its interior angles is 360; unless told
otherwise, no sides are equal and no angles are equal. However there are
several special cases.
SQUARE
In a
square, all four sides are equal and all four angles are right angles. A square
has four lines of symmetry.
RECTANGLE
In a
rectangle, the opposite sides are equal and all four angles are right angles. A
rectangle has two lines of symmetry.
PARALLELOGRAM
A
parallelogram has opposite sides that are equal and parallel, and opposite
angles that are equal. A parallelogram has no lines of symmetry but it does
have rotational symmetry of order 2.
RHOMBUS
In a rhombus the opposite angles
are equal, the opposite sides are parallel and all four sides are the same
length. A rhombus has two lines of syuunetiy (the diagonals).
KITE
A kite
has one pair of opposite angles equal and two pairs of adjacent sides equal. A
kite has one line of symmetry. It has no rotational symmetry.
TRAPEZIUM
A
trapezium has one pair of opposite sides parallel. Usually it has no line of
symmetry.
However,
in the special case when the two sloping sides are the same length there is
oneline of symmetry. This is called an isosceles trapezium. Its non-parallel
sides are e4ual andtwo pairs of adjacent angles are equal.
Transformations
A translation occurs when a shape has been moved from one place to
another. It is equivalent of picking up the shape and putting it down
somewhere else. Vectors are used to describe such
transformations.
When describing a reflection, you need to state the line which the
shape has been reflected in.
When describing a rotation, the centre and angle of rotation are
given. If you wish to use tracing paper to help with rotations: draw the
shape you wish to rotate onto the tracing paper and put this over shape.
Push the end of your pencil down onto the tracing paper, where the centre
of rotation is and turn the tracing paper through the appropriate angle.
The resultant position of the shape on the tracing paper is where the shape
is rotated to.
Enlargements
Enlargements have a centre of enlargement and a scale factor.
1) Draw a line from the centre of enlargement to each vertex ('corner') of
the shape you wish to enlarge. Measure the lengths of each of these lines.
2) If the scale factor is 2, draw a line from the centre of enlargement,
through each vertex, which is twice as long as the length you measured. If
the scale factor is 3, draw lines which are three times as long. If the
scale factor is 1/2, draw lines which are 1/2 as long.
Example:
The centre of enlargement is marked. Enlarge the triangle by a scale factor
of 2.
Vectors
A vector quantity has both length (magnitude) and direction. The opposite
is a scalar quantity, which only has magnitude. Vectors can be denoted by AB,
a, or AB (with an arrow above the letters).
If a = (3) then the vector will look as follows:
(2)
NB1: When writing vectors as one number above another in
brackets, this is known as a column vector.
NB2: in textbooks and here, vectors are indicated by bold type. However,
when you write them, you need to put a line underneath the vector to
indicate it.
Multiplication by a Scalar
When multiplying a vector by a scalar (i.e. a number), multiply each
component of the vector by the scalar.
Example:
If a = ( 3 ), and b = 2a, sketch a and b.
( 2 )
If a = ( 3 ), 2a = ( 6 )
( 2 )
( 4 )
Vector Manipulation
Example:
If a = (-5) and b = ( 2), find the magnitude of their
resultant.
( 3)
( 1)
The resultant of two or more vectors is their sum.
The resultant therefore is (-3).
( 4)
The magnitude of this is Ö(-3² +
4²) = Ö(9 + 16) = Ö(25) = 5
The addition and subtraction of vectors can be shown diagrammatically. To
find a + b, draw a and then draw b at the end
of a. The resultant is the line between the start of a and
the end of b.
To find a - b, find -b (see above) and add this to a.
Example:
Unit Vectors
A unit vector has a magnitude of 1. The unit vector in the direction of the
x-axis is i and the unit vector in the direction of the y-axis is j.
For example on a graph, 3i + 4j would be at (3 , 4). This
method is another method of writing down vectors.
Example: 3i + j plus 5i - 4j =
8i - 3j. This is equivalent to:
( 3) + ( 5 ) = ( 8 )
( 1 ) ( -4) ( -3)
special quadeilaterals
transformation
vectors
Informações
- Descrição
- form 3 maths Notas sobre shape and space 2, criado por shania catania em 25-08-2013.
- Criado por
- shania catania · ago 2013
- Atualizado
- 19 fev 2016
- Visualizações
- 110
- Tags
- Avaliação