GoConqr has a new look! Let us know what you think.

Sign up free

Quiz

DIKTA ICND2 Ch 17

Brian Gamble 6 questions

Take the quiz

Questions in this quiz (6)

  1. 1An engineer wants to set the OSPFv3 router ID for router R1. Which of the following answers could affect R1’s choice of OSPFv3 router ID?
    1. AThe ipv6 address command on interface Gigabit0/0
    2. BThe ip address command on interface Serial0/0/1
    3. CThe <b>ospf router-id</b> command in OSPFv3 configuration mode
    4. DThe ipv6 address command on interface loopback2
  2. 2Router R1 has a Serial0/0/0 interface with address 2001:1:1:1::1/64, and a G0/0 interface with address 2001:2:2:2::1/64. The OSPFv3 process uses process ID 1. Which of the following OSPFv3 configuration commands enable OSPFv3 on R1’s G0/0 interface and places it into area 0?
    1. AA network 2001:1:1:1::/64 1 area 0 command in router configuration mode
    2. BAn ipv6 ospf 1 area 0 command in G0/0 interface configuration mode
    3. CA network 2001:1:1:1::/64 1 area 1 command in router configuration mode
    4. DAn ospf 1 area 0 command in G0/0 interface configuration mode
  3. 3An enterprise uses a dual-stack model of deployment for IPv4 and IPv6, using OSPF as the routing protocol for both. Router R1 has IPv4 and IPv6 addresses on its G0/0 and S0/0/0 interfaces only, with OSPFv2 and OSPFv3 enabled on both interfaces for area 0 and the router ID explicitly set for both protocols. Comparing the OSPFv2 and OSPFv3 configuration, which of the following statements is true?
    1. AThe OSPFv3 configuration, but not OSPFv2, uses the router-id router-id router subcommand.
    2. BBoth protocols use the router-id router-idrouter subcommand
    3. CBoth protocols use the network network-number wildcard areaarea-id router subcommand.
    4. DThe both protocols use the ipv6 ospf process-id areaarea-id interface subcommand.
  4. 4R1 and R2 are routers that connect to the same VLAN. Which of the answers lists an item that can prevent the two routers from becoming OSPFv3 neighbors? (Choose three answers .)
    1. AMismatched Hello timers
    2. BMismatched process IDs
    3. CIPv6 addresses in different subnets
    4. DEqual router IDs
    5. EOne passive router interface (used on this link)
  5. 5The example shows an excerpt from the show ipv6 route ospfcommand on a router (R1). Which of the answers are correct about the interpretation of the meaning of the output of this command? (Choose two answers.)

    R1# show ipv6 route ospf
    --OI 2001:DB8:1:4::/64 [110/129]
    --------via FE80::FF:FE00:1, Serial0/0/1
    1. A110 is the metric for the route.
    2. BS0/0/1 is an interface on R1.
    3. CFE80::FF:FE00:1 is a link-local address on R1.
    4. DOI means that the route is an interarea OSPF route.
  6. 6Router R1 has been configured as a dual-stack IPv4/IPv6 router, using interfaces S0/0/0, S0/0/1, and GigabitEthernet0/1. As a new engineer hired at the company, you do not know whether any of the interfaces are passive. Which of the following commands lets you find whether G0/1 is passive, either by the command listing that fact or by that command leaving passive interfaces out of its list of interfaces ?
    1. Ashow ipv6 ospf interface brief
    2. Bshow ipv6 protocols
    3. Cshow ipv6 ospf interface G0/1
    4. Dshow ipv6 ospf interface passive

Information

Description
CCNA ICND2 (Chapter 17) Quiz on DIKTA ICND2 Ch 17, created by Brian Gamble on 10/02/2016.
Language
English
Views
52
Tags
icnd2ccnaipv6ospfchapter 17
Rating
No ratings yet
Rate this quiz
Rate this quiz

Feedback

What is it about?

What do you think of the new look?

How do you like it?