Quiz
6707- 312 Producing specialist finishes for painted decorative work
Questions in this quiz (32)
1Which type of stencil is best used for producing a complex design?
- Aa Multi plate.
- Bb Positive.
- Cc Negative.
- Dd Tied.
2The method of using an overlay of squares to enlarge or reduce an image is known as
- Aa photocopying
- Bb a grid system
- Cc illuminated projection
- Dd accurate measurement.
3What is an advantage of using acetate stencil?
- Aa Self adhesive.
- Bb Cheap to buy.
- Cc Can see previous design.
- Dd Can be used without cleaning.
4Chalking on the underside of an image prior to drawing over it is known as
- Aa photocopying
- Bb projecting
- Cc pouncing
- Dd tracing.
5The advantage of using a craft knife to cut stencils rather than a utility knife is that it has a
- Aa smaller blade
- Bb retractable blade
- Cc bigger blade
- Dd snap off blade.
6Why is glass sheet the preferred base when cutting multi plate stencils?
- Aa It is transparent.
- Bb It is readily available.
- Cc It is safer to use.
- Dd It does not scar.
7When cutting stencils, what is the approximate angle the knife should be held at?
- Aa 5-10⁰.
- Bb 20-50⁰.
- Cc 80-100⁰.
- Dd 100-120⁰.
8When cutting stencils, a large margin is used to prevent
- Aa creep
- Bb buckling
- Cc lifting
- Dd smudging.
9What is the main consideration when setting out linear runs and border stencils for wall areas?
- Aa Windows and doors.
- Bb Room dimensions.
- Cc Symmetrical balance.
- Dd Stencil size.
10What is the name given to the line which is placed on the stencil and used to level against the chalk line?
- Aa Centre line.
- Bb Horizontal line.
- Cc Vertical line.
- Dd Registration line.
11What is the main advantage of using low tack tape when securing stencil plates to finished surfaces?
- Aa It can be used again.
- Bb It does not damage the surface.
- Cc It is cheap to buy.
- Dd It is very sticky.
12What defect can occur when too much paint is applied to a stencil plate?
- Aa Cissing.
- Bb Creep.
- Cc Bittiness.
- Dd Lifting.
13What is the main cause of buckled or curled paper stencils?
- Aa Not enough sealer.
- Bb Left hanging too long.
- Cc Too much paint applied.
- Dd Not dried properly before reusing.
14What should a stencil brush be cleaned in after using water-borne stencil materials?
- Aa Brush restorer.
- Bb Warm soapy water.
- Cc White spirit.
- Dd Methylated spirit.
15How should stencil palettes be maintained and stored after use?
- Aa Stored in solvent.
- Bb Wiped clean and stacked.
- Cc Stored in lint free cloth.
- Dd Left to dry and stacked.
16The appropriate ground coat colour must be used on a wood effect to
- Aa prevent cissing
- Bb prevent fading
- Cc increase the durability
- Dd ensure a realistic effect.
17Which one of the following pigments can be used in both solvent and water borne materials?
- Aa Universal stainers.
- Bb Artists oil.
- Cc Acrylics.
- Dd Gouache.
18Which of the following colourants would be suitable to create a mahogany scumble?
- Aa Raw umber.
- Bb Brunswick green.
- Cc Burnt sienna.
- Dd Paynes grey.
19What is the final stage of the drying process for solvent borne scumble?
- Aa Coalescence.
- Bb Evaporation.
- Cc Oxidation.
- Dd Polymerisation.
20Which one of the following tools can be used to create coarse grain in oak?
- Aa Combs.
- Bb Feathers.
- Cc Flogger.
- Dd Fantail fitch.
21Which one of the following brushes is used to simulate the pore markings in oak?
- Aa Softener.
- Bb Flogger.
- Cc Overgrainer.
- Dd Mottler.
22Which one of the following tools is used to apply fine parallel grain patterns to completed work?
- Aa Softener.
- Bb Flogger.
- Cc Pencil overgrainer.
- Dd Mottler.
23Prior to storage, steel combs should be
- Aa lightly abraded
- Bb lightly oiled
- Cc degreased
- Dd primed.
24Cutting vertically through the centre of the tree trunk will reveal the pattern known as
- Aa heartwood
- Bb end grain
- Cc quarter grain
- Dd overgrain.
25Wiping out with a rag over a veining horn on wood effect is used to produce
- Aa straight grain
- Bb heartwood
- Cc mottling
- Dd flogging.
26Which one of the following describes the process to gently fade out sharp edges of a wood effect?
- Aa Overgraining.
- Bb Rubbing in.
- Cc Softening.
- Dd Combing.
27When applying a wood grain effect to a panel door where would the finishing point be?
- Aa Muntins.
- Bb Panels.
- Cc Styles.
- Dd Rails.
28How are the veins in natural marble formed?
- Aa Minerals.
- Bb Man made.
- Cc Limestone.
- Dd Crystallisation.
29Which one of the following is the BS4800 groundcoat colour for Vert de mer?
- Aa 00E53
- Bb 20E51
- Cc 00E55
- Dd 00A01
30Which one of the following is the main pigment colour used in black and gold?
- Aa Sienna.
- Bb Ultramarine blue.
- Cc Brunswick green.
- Dd Umber.
31Which one of the following is the main tool used to produce marble effects?
- Aa Check roller.
- Bb Dragger.
- Cc Veining horn.
- Dd Feather.
32Which one of the following brushes is best suited to producing veins in marble?
- Aa Flogger.
- Bb Softener.
- Cc Dragger.
- Dd Sable.
Information
- Description
- A test on producing specialist finishes
- Author
- james crowley
- Language
- English
- Views
- 435
- History
- Created on 4 May 2017 · updated on 4 May 2017
- Tags
- Rating
- No ratings yet Rate this quiz