Wireless Fundamentals 6 - Foreign

1. 1When using multiple SSIDs on a lightweight AP, how does the traffic of each SSID reach the 802.3 network?

   1. Aprovide routing between them at the core so that the SSIDs can reach the internet
   2. Bconfigure 802.11q trunking on the Ethernet switch port that is connected to the AP
   3. Cconfigure ACLs at the switch port that will allow all desired SSIDs to pass traffic
   4. Dconfigure the SSIDs on the WLC and it will regulate the traffic based on traffic type
2. 2When a guest client is authenticated, which type of connection is created between the
   controller-based AP and the client?

   1. Aa SSL connection
   2. Ba TLS encrypted tunnel
   3. Can unsecured connection
   4. Da 802.1x/EAP tunnel
   5. Ean IPsec tunnel
3. 3An engineer wants to deploy a 2504 controller as the anchor controller for a guest WLAN that resides on a 5508 controller in a different mobility group. What configuration change must be applied to support this deployment strategy?

   1. AUDP 16666 and IP Protocol 97 must be enabled on the 2504 controller
   2. BUDP 5246 and TCP Protocol 97 must be enabled on the router
   3. CThe 2504 controller must be added to the same mobility group as the 5508.
   4. DDHCP Option 43 must be added to the neighboring switchport
4. 4Which four parameters must be configured for local EAP-FAST on the controller? (Choose four.)

   1. Aauthority ID
   2. Bauthority ID Information
   3. Cclient key
   4. DPAC
   5. Eserver key
   6. FTTL for PAC
   7. Gmonitor key
   8. HNTP source
5. 5After you configure the Cisco 5508 Wireless Controller v7.6, a customer requests an SSID that allows for client web authentication with email input. Which authentication method should be used?

   1. Apass-through
   2. Bauthentication
   3. Csplash page web redirect
   4. Dconditional web redirect
   5. Eon MAC filter failure
6. 6When a wireless guest network is implemented using auto-anchor mobility in a controller- based wireless network, which controller is responsible for a guest client's IP address and their security configuration?

   1. Aany controller that supports the same VLAN
   2. Bforeign controller
   3. Canchor controller
   4. Dmaster controller
   5. ERF group master controller
7. 7Which three severity levels are in the Cisco WCS alarm dashboard? (Choose three.)

   1. ACritical
   2. BFlash
   3. CMajor
   4. DMinor
   5. ETrivial
   6. FUrgent
8. 8When adding a controller to manage through Cisco WCS, which address type is used and which SNMP function does the Cisco WCS perform?

   1. AThe controller is managed through its MAC address and the Cisco WCS acts as a SNMP TRAP authenticator.
   2. BThe IP address of the controller is used and the Cisco WCS acts as a SNMP TRAP receiver.
   3. CThe controller is managed through its MAC address and the Cisco WCS acts as a SNMP agent.
   4. DThe controller connects through its MAC address to the Cisco WCS and the Cisco WCS uses the SNMP to manage the controller for all configured SNMP parameters.
9. 9Which user group has the ability to configure all features of the Cisco WCS except the user accounts and passwords?

   1. AAdmin
   2. BSuperUser
   3. CRoot
   4. DSuperVisor
10. 10A customer has requested a single point of policy enforcement for LAN and WLAN. Which deployment model should be used?

    1. Aconverged
    2. Bautonomous
    3. CFlexConnect
    4. Dcentralized

11. 11How does an LWAP receive a configuration file?

    1. AIt is configured manually.
    2. BIt receives a configuration from the controller.
    3. CIt automatically ships with a configuration.
    4. DIt receives a configuration from a TFTP server.
12. 12Which RRM feature allows an access point to avoid non-IEEE 802.11 interference?

    1. ADCA
    2. BTPC
    3. CRF groups
    4. Dcoverage hole detection
13. 13Which two Cisco WLC management-access methods are available as the default setting? (Choose two.)

    1. ASSH
    2. BHTTPS
    3. CTelnet
    4. DHTTP
14. 14Refer to the exhibit. An engineer is testing client connectivity and is unable to transmit or receive at IEEE 802.11n high throughput rates. Which two Layer 2 security configurations allow the client to successfully connect at 802.11n rates? (Choose two.)

    

    1. AWPA2-AES 802.1x
    2. BWPA2-TKIP PSK
    3. CWPA-TKIP 802.1x
    4. DOpen
    5. E802.1x
15. 15What protocol is used to determine the best pathway back to a root access point?

    1. ACCKM
    2. BWNMP
    3. CAWPP
    4. DLWAP
16. 16What protocol overcomes the weaknesses of LEAP?

    1. AEAP-TLS
    2. BPEAP
    3. CEAP-FAST
    4. DEAP-TTLS
17. 17During an upgrade, the wireless infrastructure has seen a few access points join and then drop off the network. After further investigation, it appears the access points may have an IOS code version that is causing issues. Where in the controller is this information found?

    1. AGUI > Wireless > Access Point > General
    2. BCLI > show ap image all
    3. CGUI > Monitor > Software Version
    4. DCLI > show sysinfo
18. 18The new tablets for the sales department require an SNR of 18 or more to operate. Given a noise floor of -88 dBm, what is the minimum RSSI that is needed?

    1. A-60 dBm
    2. B-70 dBm
    3. C-72 dBm
    4. D-80 dBm
    5. E-96 dBm
    6. F-106 dBm
19. 19Which four options are the characteristics of the original 802.11 protocol? (Choose four.)

    1. ADefined DSSS and FHSS as possible methods for modulation
    2. BDesigned to operate in the 5 GHz ISM frequency spectrum
    3. CThe most common deployment is three non-overlapping channels that are 20 MHz wide
    4. DThe protocol sets the maximum throughput at 1 Mb/s or 2 Mb/s
    5. EDefined FHSS and OFDM as possible methods for modulation
    6. FThe most common deployment is three non-overlapping channels that are 22 MHz wide
    7. GDesigned to operate in the 2.4 GHz ISM frequency spectrum
    8. HThe protocol sets the maximum throughput at 1 Mb/s
20. 20Which three options relate to event-driven RRM? (Choose three.)

    1. Aany 802.11n AP models
    2. Bspecific AP models
    3. Cminimum of AP and WLC
    4. Dminimum of AP, WLC, and WCS
    5. Eminimum of AP, WLC, WCS, and MSE
    6. Fconfigurable in WLC at 802.11b/g/n > RRM > TPC
    7. Gconfigurable in WLC at 802.11b/g/n > RRM > DCA
21. 21Which protocol is used for Cisco WCS to communicate with Cisco WLC?

    1. ASNMP
    2. BCAPWAP
    3. CHTTPS
    4. DSSH
22. 22Which two factors must be considered when evaluating an RF interferer for severity?
    (Choose two.)

    1. Adistance from the AP
    2. BdBm
    3. Cthe type of security crack being used
    4. Dduty cycle
    5. Enumber of interfering IP stations in the cell
    6. Fduplicate SSID
23. 23Following the deployment of a wireless network for data and voice services, an engineer is to validate the coverage. Which type of survey is required to ensure coverage?

    1. Apassive
    2. Bactive
    3. Cfingerprinting
    4. Dcalibrating
24. 24You are on the phone working with a colleague that is console connected to a lightweight AP that has lost its configuration. Which three actions are necessary to allow the AP to connect to a controller? (Choose three.)

    1. AConfigure the AP IP address.
    2. BConfigure the controller name.
    3. CConfigure the controller IP address.
    4. DConfigure the AP hostname.
    5. EConfigure the AP IP default-gateway.
    6. FConfigure the AP username and password.
25. 25Which of the following are three functions of Cisco RRM? (Choose three.)

    1. ATPC
    2. Bintercontroller roaming
    3. Cdynamic channel assignment
    4. Dintracontroller roaming
    5. Ecoverage hole detection

Description

CCNA WIRELESS Quiz on Wireless Fundamentals 6 - Foreign, created by I L on 29/06/2017.

Author

I L

Language

English

Views

7

Tags

wirelessccna

Rating

No ratings yet

Rate this quiz

Rate this quiz

More on Wireless LAN Controllers