12381849
Description
Flashcards by Ralf Messner, updated more than 1 year ago
|
Created by Ralf Messner
about 6 years ago
|
|
| Question | Answer |
| Which three statements accurately describe Layer 2 Ethernet switches? (Choose three.) A. Spanning Tree Protocol allows switches to automatically share VLAN information. B. Establishing VLANs increases the number of broadcast domains. C. Switches that are configured with VLANs make forwarding decisions based on both Layer 2 and Layer 3 address information. D. Microsegmentation decreases the number of collisions on the network. E. In a properly functioning network with redundant switched paths, each switched segment will contain one root bridge with all its ports in the forwarding state. All other switches in that broadcast domain will have only one root port. F. If a switch receives a frame for an unknown destination, it uses ARP to resolve the address. | Answer: B,D,E |
| A receiving host computes the checksum on a frame and determines that the frame is damaged. The frame is then discarded. At which OSI layer did this happen? A. session B. transport C. network D. data link E. physical | Answer: D |
| A network interface port has collision detection and carrier sensing enabled on a shared twisted pair network. From this statement, what is known about the network interface port? A. This is a 10 Mb/s switch port. B. This is a 100 Mb/s switch port. C. This is an Ethernet port operating at half duplex. D. This is an Ethernet port operating at full duplex. E. This is a port on a network interface card in a PC. | Answer: C |
| What is the difference between a CSU/DSU and a modem? A. A CSU/DSU converts analog signals from a router to a leased line; a modem converts analog signals from a router to a leased line. B. A CSU/DSU converts analog signals from a router to a phone line; a modem converts digital signals from a router to a leased line. C. A CSU/DSU converts digital signals from a router to a phone line; a modem converts analog signals from a router to a phone line. D. A CSU/DSU converts digital signals from a router to a leased line; a modem converts digital signals from a router to a phone line. | Answer: D |
| A router has two Fast Ethernet interfaces and needs to connect to four VLANs in the local network. How can you accomplish this task, using the fewest physical interfaces and without decreasing network performance? A. Use a hub to connect the four VLANS with a Fast Ethernet interface on the router. B. Add a second router to handle the VLAN traffic. C. Add two more Fast Ethernet interfaces. D. Implement a router-on-a-stick configuration. | Answer: D |
| In an Ethernet network, under what two scenarios can devices transmit? (Choose two.) A. when they receive a special token B. when there is a carrier C. when they detect no other devices are sending D. when the medium is idle E. when the server grants access | Answer: C,D |
| Where does routing occur within the DoD TCP/IP reference model? A. application B. internet C. network D. transport | Answer: B |
| For what two purposes does the Ethernet protocol use physical addresses? (Choose two.) A. to uniquely identify devices at Layer 2 B. to allow communication with devices on a different network C. to differentiate a Layer 2 frame from a Layer 3 packet D. to establish a priority system to determine which device gets to transmit first E. to allow communication between different devices on the same network F. to allow detection of a remote device when its physical address is unknown | Answer: A,E |
| Which layer in the OSI reference model is responsible for determining the availability of the receiving program and checking to see if enough resources exist for that communication? A. transport B. network C. presentation D. session E. application | Answer: E |
| Which of the following correctly describe steps in the OSI data encapsulation process? (Choose two.) A. The transport layer divides a data stream into segments and may add reliability and flow control information. B. The data link layer adds physical source and destination addresses and an FCS to the segment. C. Packets are created when the network layer encapsulates a frame with source and destination host addresses and protocol-related control information. D. Packets are created when the network layer adds Layer 3 addresses and control information to a segment. E. The presentation layer translates bits into voltages for transmission across the physical link. | Answer: A,D |
| Which of the following describes the roles of devices in a WAN? (Choose three.) A. A CSU/DSU terminates a digital local loop. B. A modem terminates a digital local loop. C. A CSU/DSU terminates an analog local loop. D. A modem terminates an analog local loop. E. A router is commonly considered a DTE device. F. A router is commonly considered a DCE device. | Answer: A,D,E |
Want to create your own Flashcards for free with GoConqr? Learn more.