Help shape GoConqr. What should we add next?

Quiz

CCNA – EtherChannel

jonathan rozo 5 questions

Take the quiz

Questions in this quiz (5)

  1. 1QUESTION NO: 286
    Refer to the exhibit.
    A network administrator is configuring an EtherChannel between SW1 and SW2. The SW1 configuration is shown. What is the correct configuration for SW2?

    Image for question 1
    1. Ainterface FastEthernet 0/1
      channel-group 1 mode active
      switchport trunk encapsulation dot1q
      switchport mode trunk
      interface FastEthernet 0/2
      channel-group 1 mode active
      switchport trunk encapsulation dot1q
      switchport mode trunk
    2. Binterface FastEthernet 0/1
      channel-group 2 mode auto
      switchport trunk encapsulation dot1q
      switchport mode trunk
      interface FastEthernet 0/2
      channel-group 2 mode auto
      switchport trunk encapsulation dot1q
      switchport mode trunk
    3. Cinterface FastEthernet 0/1
      channel-group 1 mode desirable
      switchport trunk encapsulation dot1q
      switchport mode trunk
      interface FastEthernet 0/2
      channel-group 1 mode desirable
      switchport trunk encapsulation dot1q
      switchport mode trunk
    4. Dinterface FastEthernet 0/1
      channel-group 1 mode passive
      switchport trunk encapsulation dot1q
      switchport mode trunk
      interface FastEthernet 0/2
      channel-group 1 mode passive
      switchport trunk encapsulation dot1q
      switchport mode trunk
  2. 2QUESTION NO: 292
    Refer to the exhibit.
    If the devices produced the given output, what is the cause of the EtherChannel problem?

    Image for question 2
    1. ASW1's Fa0/1 interface is administratively shut down.
    2. BThere is an encapsulation mismatch between SW1's Fa0/1 and SW2's Fa0/1 interfaces.
    3. CThere is an MTU mismatch between SW1's Fa0/1 and SW2's Fa0/1 interfaces.
    4. DThere is a speed mismatch between SW1's Fa0/1 and SW2's Fa0/1 interfaces.
  3. 3QUESTION NO: 294
    A network administrator creates a layer 3 EtherChannel, bundling four interfaces into channel group 1. On what interface is the IP address configured?

    1. Athe port-channel 1 interface
    2. Bthe highest number member interface
    3. Call member interfaces
    4. Dthe lowest number member interface
  4. 4QUESTION NO: 288
    What parameter can be different on ports within an EtherChannel?

    1. Aspeed
    2. BDTP negotiation settings
    3. Ctrunk encapsulation
    4. Dduplex
  5. 5QUESTION NO: 290
    Refer to the exhibit.


    What set of commands was configured on interface Fa0/3 to produce the given output?

    Image for question 5
    1. Ainterface FastEthernet 0/3
      channel-group 1 mode desirable
      switchport trunk encapsulation dot1q
      switchport mode trunk
    2. Binterface FastEthernet 0/3
      channel-group 2 mode passive
      switchport trunk encapsulation dot1q
      switchport mode trunk
    3. Cinterface FastEthernet 0/3
      channel-group 2 mode active
      switchport trunk encapsulation dot1q
      switchport mode trunk
    4. Dinterface FastEthernet 0/3
      channel-group 2 mode on
      switchport trunk encapsulation dot1q
      switchport mode trunk

Information

Description
Quiz on CCNA – EtherChannel , created by jonathan rozo on 13/06/2016.
Language
Español
Views
3
Rating
No ratings yet
Rate this quiz
Rate this quiz

More on EtherChannel and Link Aggregation

Feedback

What is it about?

What should we add next?