Flashcards
IE 21 LE3

Cards in this deck (153)
- 1Uses a media (abrasive) propelled into the surface using air, water, or even a wheel Abrasives, CO2, are mechanically impelled against the surface to be cleanedBlast Cleaning

- 2Also tumbling Effective means of finishing large numbers of small parts barrel drumBarrel Finishing

- 3Versatile process widely used for deburring, radiusing (corner rounding), descaling, burnishing, cleaning, brightening, and fine finishing performed in open containers 900 and 3600 cycles per minuteVibratory Finishing

- 4Workpieces are held against a moving abrasive belt. Resulting surface contains a series of parallel scratches with a texture set by the grit of the beltbelt grinder

- 5used to clean surfaces and impart some small degree material removal or soothing Resulting surface consists of a series of uniform curved scratcheswire brushing

- 6A polishing operation in which workpiece is brought into contact with a revolving cloth wheel that has been charged with a fine abrasive such as polishing rougebuffing

- 7Employs a DC electrolytic circuit with a workpiece as the anode As current is applied, material is stripped from the surface, with material removal occurring preferentially from any RAISED locationelectropolishing

- 8Effective means of removing oil, dirt, scale, or other foreign material that may adhere to the surface of the product, as a preparation for subsequent painting or platingChemical Cleaning
- 9Removing a wide variety of soils (oils, grease, wax, fine particles of metal and dirt) cleaners are usually complex solutionalkaline cleaning

- 10what are used to reduce surface tension and displace, emulsify, and disperse the insoluble soilssurfactants or soaps
- 11Oils, grease, fats, and other surface contaminants are removed by dissolving them in organic solvents derived from coal or petroleum usually at room temperatureSolvent Cleaning

- 12Vapors of chlorinated or fluorinated solvent are used to remove oil, grease, and wax from metal products. A nonflammable solvent such as trichloroethylene is heated to its boiling point, and the parts to be cleaned are suspended in its vapors.Vapor Degreasing
- 13parts are suspended or placed in wire-mesh baskets that are then immersed in a liquid cleaning bath, often a water-based detergent. The bath contains an ultrasonic transducer that operates at a frequency that causes cavitation in the liquid. excellent results can usually be obtained in 60 to 200 seconds.Ultrasonic Cleaning

- 14Metal parts are first cleaned to remove oils and other contaminants and then dipped into dilute acid solutions to remove oxides and dirt that are left on the surface by previous processing operationsAcid Pickling

- 15applied to the surface of a workpiece (substrate) for decorative and/or functional purposes such as imparting corrosion resistanceSurface Coatings
- 16most common carrying vehicle for the pigments in paintingwater
- 17most widely used finish on manufactured productspaints and enamels
- 18consist of thermoplastic polymers dissolved in organic solvent. Although fast drying (by the evaporation of the solvent) and capable of producing very beautiful finishes, they are not sufficiently durable for most commercial applications.Nitrocellulose lacquers
- 19are a general-purpose paint but are not adequate for hard-service applications.alkyds
- 20widely used for automotive finishes and may require catalytic or oven curing.Acrylic enamels
- 21solutions of asphalt in a solvent; are used extensively in the electrical industry, where resistance to corrosion is required and appearance is not of prime importanceAsphaltic paints
- 22a simple and economical means of paint application when all surfaces of the part are to be coated. The products can be manually immersed into a paint bath or passed through the bath while on or attached to a conveyordipping
- 23probably the most versatile means of application but can be quite costly in terms of labor and production time; workers must exercise considerable skill to obtain the proper coverage.hand spraying
- 24some form of parts conveyor that transports the parts past a series of stationary spray heads; industrial robots can be used to move the spray heads in a manner that mimics the movements of a human painter, maintaining uniform separation distance and minimizing waste.Automatic spraying
- 25a DC electrostatic potential is applied between the atomizer and the workpieceelectrostatic deposition

- 26is another variation of electrostatic spraying but the particles are solid rather than liquidpowder coating

- 27most widely used method of imparting corrosion resistance to steel; fluxed by dipping into a solution of zinc ammonium chlorideHot-dip coating/galvanizing

- 28the surface of the metal is chemically treated to produce a nonmetallic, nonconductive surface that can impart a range of desirable properties; conversion coatings are chromate and phosphatechemical conversion coating
- 29produce a black, iron oxide coating—a lustrous surface that is resistant to rusting when handled; type of oxide forms at elevated temperatures; spent carburizing compound or special blackening saltsBlackening or Coloring Metals

- 30a DC voltage is applied between the parts to be plated (which is made the cathode) and an anode material that is either the metal to be plated or an inert electrodeElectroplating

- 31T or F: Plastics can be electroplated, provided that they are first coated with an electrically conductive material.T
- 32an electrochemical process, that is somewhat the reverse of electroplating, which produces a conversion-type coating on aluminum that can improve corrosion and wear resistance and impart a variety of decorative effects a reaction progresses inward, increasing the thickness of the hard hexagonal aluminum oxide crystals on the surfaceanodizing

- 33complex plating solutions (containing metal salts, reducing agents, complexing agents, pH adjusters, and stabilizers) are brought into contact with a substrate surface that acts as a catalyst or has been pretreated with catalytic material. doesn’t use electric current the coatings are uniform in thickness, independent of part geometry. The rate of deposition is considerably slower than with electroplatingElectroless plating

- 34also known as peen plating or impact plating, is an adaptation of barrel finishing in which coatings are produced by cold-welding soft, malleable metal powder onto the substrate. Numerous small products are first cleaned and may be given a thin galvanic coating of either copper or tin. placed in a tumbling barrel, along with a water slurry of the metal powder to be plated, glass or ceramic tumbling media, and chemical promoters or acceleratorsMechanical Plating

- 35metals are coated with a variety of glassy, inorganic materials that impart resistance to corrosion and abrasion, decorative color, electrical insulation, or the ability to function in high-temperature environments. multicomponent suspension or slurryporcelain enameling

- 36large class of materials consisting of many small molecules (called monomers)polymers (macromolecules)
- 37main source of synthetic plasticcrude oil
2nd: coal, natural gas - 38how are plastics formed?When monomers are linked together in the
process of polymerization - 39general properties of plasticslight in weight
good corrosion resistance
resistance to chemicals
good electrical resistance
good for insulating electrical materials
lower thermal conductivity than
metals and thus are good heat insulators
inferior to engineering metals with respect to strength
dimensional stability are greatly inferior to metals - 40uses of plasticsPackaging or container materials
Insulators in electrical equipment and as handles for hot articles (due to their low electrical and/or thermal conductivity) - 41type of plastic that's resistant to breakdown from chemical and thermal attack and weatheringthermosetting plastics
- 42soften with increasing temperature and become harder and stronger with decreasing temperature; no chemical change is involved Return to their original properties when cooledthermoplastics
- 43Typical applications: bearings, cams, gears, bushings, rollers, valves, pipesacetals
- 44Highest optical clarityacryclics
- 45Contains acrylonitrile, butadiene, or styrene applications: in - service conditions are quite severeAcrylonitrile-Butadiene-Styrene (ABS)
- 46Weather poorly and are affected by heat and chemicalsCellulosics
- 47Has high moisture absorption and is affected by alcohols and alkalisCellulose acetates
- 48Developed to have better impact strength and moisture resistance than cellulose acetate application: withstand rough usageCellulose acetate butyrate
- 49In pharmaceuticals they mask the taste of bitter actives, enhance the strength and appearance of tablets and capsules, and enable controlled release formulationsEthyl cellulose
- 50Has a low coefficient of frictionFluorocarbons
- 51Two types: nylons and aramidsPolyamides
- 52Hygroscopic - absorbs waterNylons
- 53ballistic and stab resistant body armorAramids
Kevlar® is an aramid, it is lightweight
and extraordinarily strong, with five
times the strength of steel on an equal weight basis - 54Hydrophobic and quick dryingPolyesters
- 55Low-density PE (LDPE), Medium- density PE (MDPE), High-density PE (HDPE)Polyethylene(PE)
- 56One of the lightest plastics Improved strength, stiffness and higher temperature capability over polyethylenePolypropylene
- 57Citrus juices and cleaning fluids affect it adversely and it burns readilyPolystyrenes
- 58Used in medical and sterilizing equipmentPolysulfones
- 59Resistant to acids and alkalisVinyls
- 60Do not become soft to any significant extent with increasing temperature. More rigid and harder than thermoplasticsthermosets
- 61—thermoplastic


- 62—thermoset


- 63Typical applications: electrical and electronic components, enamelsAlkyds
- 64Typical applications: small appliance housing, countertops, toilet seats, handlesaminos
- 65Widely used for containers and housings but should not be used outdoors Typical applications: lighting fixtures, adhesives, finishes, medium -density fiberboard (MDF), electrical components and sometimes molded into objectsUrea formaldehyde
- 66Typical applications: tools and dies, adhesives, tanksepoxies
- 67Typical application: dinnerwaresmelamines
- 68Typical applications: knobs, handles, telephones, laminated panelsphenolics
- 69Application: casting and encapsulation, bonding of other materialspolyester
- 70Application: tubingPolyimides
- 71added to improve strength or to decrease cost; they also aid in controlling shrinkage; the most common are wood flour, cloth fibers, glass fibersfillers
- 72added in small amounts to increase and control the flow of the plastic during molding; the amount is held to a minimum because it is likely to affect the stability of the finished product through gradual loss during aging.Plasticizers
- 73may either be dyes, which actually alter the color of the resin, or colored pigments that through their presence impart a desired color.coloring agents
- 74added in small amounts to increase and control the flow of the plastic during molding; wax, stearates, and occasionally soaps are examples to uselubricants
- 75simplest of the processes because no fillers are used and no pressure is involvedcasting
- 76used extensively for making hollow products, such as bottles and other containersblow molding
- 77the raw material is pressed to shape while cold, is then removed from the mold and baked in an oven until curing is completecold molding
- 78almost exclusively used for thermosetting materialsHot-Compression Molding
- 79used to avoid the turbulence and uneven flow that often result from the non-uniform, high pressures in hot-compression moldingTransfer Molding
- 80used to produce more thermoplastic products than any other processInjection Molding
- 81modified injection molding process used for thermosetting plasticsJet Molding
- 82Used to form large or small hollow shapes using powdered plasticRotational Molding
- 83the plastic material is fed from a hopper into a screw chamber from whence the rotating screw conveys it through a preheating chamber, where it is compressed, and then forces it through a heated die and onto a conveyor belt.Extrusion
- 84process in which sheets of paper, or cloth made from glass or other types of fibers, are impregnated with thermosetting liquid resin and then placed together to build up a desired thicknesslaminating
- 85used extensively to form shapes from thermoplastic materialsVacuum Forming
- 86made by combining with the plastic resin a foaming agent that releases gas when the combination is heated during moldingFoamed Plastics
- 87traditionally only used in joining thermoplastics involves coating plastics with a solvent and clamping them togetherSolvent Bonding
- 88used when precision bonding is not required. This is the simplest way of joining plastics; suited for joining stronger plastics.Mechanical Fastening
- 89Surface Preparation of Plastics1. Wash the plastic object to be painted
2. Pretreat using abrasives, chemical etching, corona discharge, combustion spray, plasma spray, or lasers
3. When sanding is used to abrade the
substrate, the grit must be fine enough to prevent scratch or gouge marks on the surface that will show through the paint - 90What do you add to your paint if the plastic object is flexible.plastic flex agent
- 91electroplating plastics steps1. Etch in chromic acid based solution to promote adhesion
2. Neutralise excess chromic acid
3. Activate the plastics surface with a solution containing tin and palladium salts that catalyse nickel or copper growth from the subsequent electroless processes
4. Coat the surface with either nickel or copper - 92they can be stretched up to at least twice their original length and upon immediate release of the stress will return quickly to approximately their original lengthelastomers
- 93is elastic and water-resistant, traps air (so it floats), and doesn't conduct electricity. In its unprocessed form, it's used in the following sample applications: as adhesives, contraceptives, and latex balloonsrubber
- 94is harder, less elastic, and more durable and has many more uses, from vehicle tires to hose pipes and from artificial hearts to waterproof gasketsVulcanized Rubber
- 95still the biggest single use of rubber in the world. About half of all the world's rubber ends up wrapped around the wheels of cars, bicycles, and truckstires
- 96The source of natural rubber which are tapped to obtain the sap, called the latex, composed of about 65% water and 35% rubberHevea Brasiliensis trees
- 97steps in rubber production1. a special tapping knife is used to cut a thin layer of the rubber tree's bark. Care must be taken so as not to cut too deep as this will injure the tree.
2. the latex flows into the cup attached to the tree. by noon or early afternoon, the latex will have stopped flowing.
3. the rubber tapper will go back to each tree and empty the latex collected by the cup into the tin
4. the latex is poured into molds. formic acid is added to coagulate the liquid latex.
5. the formic acid transforms the liquid latex into a firm solid block of rubber.
6. the block of rubber is initially rolled in a wooden roller to make it thin enough to roll in a mangle machine.
7. the rubber sheet is manually rolled by the mangle several times to make it thinner by squeezing out the water, which makes it easier for the sheet to dry.
8. the sheets are air-dried. the dried sheet is known as pale crepe. it can also be dried in smokehouses, which results in a smoked crepe.
9. the dried rubber sheet is golden brown as opposed to white initially.
10. the dried rubber sheets are pressed into - 98masticating machines "chew up" raw rubber using mechanical rollers and presses to make it softer, easier to work, and more stickymastication
- 99unprocessed rubber processes1. mastication
2. mixing
3. vulcanizing - adding sulfur and heating rubber at a suitable temperature imparts strength to it - 100The earliest synthetic rubbers; most commonly used elastomer because of its low cost and good propertiesStyrene Butadiene Rubbers
- 101useful at elevated temperatures and is used for heavy-duty applications Soft, foamy, insulating rubber Used in wet suitsneoprene (polychloroprene)
- 102Urethane elastomers are calledspandex
- 103same molecular structure as natural rubberPolyisoprene
- 104the hard fibrous material that forms the main substance of the trunk or branches of a tree or shrubwood
- 105weight for weight is one of the strongest and stiffest of all materialswood
- 106produces a seed, which grows in a cone. Used for general structural purposes; example: pinesoftwood
- 107produces a flower, has a seed which is protected by an exterior coating and has broad leaves. Fruit trees are good examples Used for interior finish, furniture, cabinetwork; examples: ipil, kamagong, narra, yakalhardwood
- 108Cutting down of trees in the forest, trimming off branches and vegetationlogging
- 109At the sawmill the logs are sawed into the commercial sizes of lumber, either byrotary or band saws
- 110its objective is to bring to equilibrium the state of the wood to that of the atmosphere with respect to moistureseasoning
- 111Without this, shrinkage will develop because of water loss and cell contractionseasoning
- 112Reduces the moisture content from about 32 to 13%air drying
- 113a brick drying chamber with heating Nails pipes through the floor or ceiling, fans to circulate the air, and jets to introduce steam to humidify the air and avoid rapid evaporationkiln
- 114manufactured from thin sheets of cross- laminated veneer and bonded under heat and pressure with strong adhesivesplywood
- 115plywood vs solid wood

- 116the reduction in size of wood by means of a saw blade; the most common tool used is the radial sawcutting
- 117the process of using a very sharp blade to shave off pieces of woodplaning
- 118Used to create shapes using a wood lathewood turning
- 119have greater holding power than nails; Work fastened by this can be easily taken apart and put together again without damaging the workscrews
- 120Neatest, most durable, and strongest wood fastener when properly usedglues
- 121are hardwood rods inserted in drilled holesdowels
- 122protective coatingpainting
- 123used to tint the wood.staining
- 124Lightens the color of wood by means of chemicalsBleaching or Blonding
- 125uses finishes that are clear protective coatings that sit on or in the surface of the woodfinishing
- 126offer less protection but are also easier to apply which is their primary advantageoils
- 127one of the most protective finishes available; they are slow drying which can allow dust and dirt time to settle and damage the finishvarnishes
- 128one of the few natural resins still in use today; alcohol based which makes it very fast dryingshellac
- 129used most often in furniture factories because its fast drying properties reduce dust related finish problems.lacquer
- 130are basically latex paint without a pigment. The two primary downsides are that they tend to hold visible brush marks and are less durable than the more conventional finishedWater-based Finishes
- 131an inorganic substance in a condition which is continuous and is analogous to the liquid stateglass
- 132properties of glass- Amorphous(no clearly defined shapeor form) solid with the structure of a liquid, behavior is similar to that of amorphous alloys
- No distinct melting or freezing point
- Low conductivity
- High electrical resistivity
- Low thermal expansion(near-zero)
- Optically transparent
-Of considerable strength, but compared to metals, is a brittle material; strongly bonded glasses like silica (SiO2 ) have the greatest strength - 133Excellent container material for chemicals. The only substance that attacks it rapidly is hydrofluoric acidglass
- 134The great bulk of the glass produced today is of the This glass is used for container and sheet glasssoda-lime-silica type with a small addition of alumina
- 135is quite similar to the container glass except that it is lower in iron content and often contains barium oxide for greater brillianceGlass for tableware
- 136is used for the highest grade of artware, especially when it is to be cut or engraved. This glass contains a considerable proportion of lead oxide which increases the index of refraction and thus gives greater brilliance. The lead also makes glass softer for cutting.flint glass or crystal
- 137have the advantages of low thermal expansion, high softening point, and good chemical resistance. They are much used for laboratory and cooking wareHigh silica glasses of the Pyrex® type
- 138must have a considerable range of index of refraction and dispersionoptical glasses
- 139Used in 90% of today's flat glass production. The raw materials are properly weighed, mixed, and then introduced into a furnace where they are melted at 1500°C. The molten glass then flows from the glass furnace onto a bath of molten tin in a continuous ribbonfloat glass
- 140Smooths out the edges and seams by localized application of heatFire Polishing
- 141Passing under felt laps fed with a suspension of fine rouge (Fe2O3 ) in waterGrinding and Polishing
- 142Gradual cooling down at a given rate in a lehr or annealing ovenAnnealing
- 143Is an inorganic, nonmetallic solid material comprising metal, nonmetal or metalloid atoms primarily held in ionic and covalent bonds.ceramic
- 144Traditional ceramics▪ clay products,
▪ silicate glass and
▪ cement - 145Advanced ceramics▪ carbides (SiC),
▪ pure oxides (Al2O3 ),
▪ nitrides (Si3N4 ),
▪ non-silicate glasses and many others - 146are fine-grain mixture of several minerals which form a plastic mass with water. The plastic mass, after drying, retains any shape imparted to it and acquires the strength of stone when it has been firedclay
- 147steps in processing clay1. mining
2. Comminution (clay particles are reduced in size)
3.Sizing and classification (passing the clay through different size mesh made of steel or bronze wire.)
4. Disintegration into finer particles
5. Chemical treatment
6. Removal of impurities
7. water removal
8.Drying
9. storage - 148uses pressure to compact ceramic powder into the desired shape which is then sintered.Powder pressing
- 149consists of forcing a plastic mix of a ceramic powder through a constricting die to produce elongated shapes that have a constant cross- sectionextrusion
- 150turns out products due to revolution such as saucers, plates, bowls, etc. Jiggering forms the external shape and jollying forms the internal shapeSoft plastic molding
- 151refers to the filling of a mold with a slip consisting of a suspension of ceramic particles in liquidSlip casting
slip (suspended ceramic particles + organic liquid) - 152consolidation of ceramic powder particles by heating the “green” compact part to a high temperature below the melting point, when the material of the separate particles diffuse to the neighboring powder particlesSintering(Firing)
- 153covers the ceramic with a surface coating that becomes glass-like or vitreous when firedglazing
Information
- Description
- Flashcards on IE 21 LE3, created by Suzzane Castro on 10/12/2022.
- Created by
- Suzzane Castro
- Views
- 4
- Rating
More on Machining and Machine Tools