GoConqr has a new look! Let us know what you think.

Flashcards

Network Media, Devices, and Standards

Joseph Rubino NetSec Foundations GRE English 22 cards

Cards in this deck (22)

  1. 1ModemConverts digital data to analog signals and vice versa for transmission over phone and cable lines. Operates at the Physical and Data Link Layer of the OSI model.
  2. 2SwitchConnects devices within a single network. More complex version of a hub in that you can add security measures. Operates at the Data Link and Network Layer of the OSI model.
  3. 3RouterForwards data packets between networks. Operates at the Network Layer of the OSI model.
  4. 4BridgeSimilar to a router in that it connects 2 or more networks. The difference is that it doesn't analyze data packets and simply forwards data to next network. Not widely used. Operates at the Data Link Layer.
  5. 5RepeaterA device used to strengthen, replicate, and regenerate signals. Example is a range extender. Physical Layer of the OSI model
  6. 6HubConnects the router to the network, takes the data packets from the router and sends to all devices connected on the network. (example is a usb hub). Physical Layer of the OSI model
  7. 7What is a UTP cable?Unshielded Twisted Pair (UTP) cables consist of pairs of wires twisted around each other to cancel out interference. Invented by Alexander Graham Bell in 1881, these cables are used for analog phone lines and copper Ethernet cables.
  8. 8How are UTP cables categorized?UTP cables are categorized into different types (Cat3, Cat4, Cat5, Cat5e, Cat6, Cat6a) as defined by TIA/EIA 568, based on their support for transmission speeds and lengths.
  9. 9Cat3supports up to 10 Mbps (Megabits per second) for up to 100 meters and is commonly used for phone lines today.
  10. 10Cat4supports 16 Mbps for up to 100 meters and is not commonly used today.
  11. 11Cat5used in Ethernet LANs containing two twisted pairs allowing for up to 100 Mbps up to 100 meters between the device and the switch, hub, or router. This has been practically replaced by the Cat5e specification.
  12. 12Cat5edoubles the number of twisted pairs to four for up to 1 Gbps (Gigabits per second) over up to 100 meters
  13. 13Cat6Used in Ethernet LANs and data centers. Cat6 is made up of four tightly woven twisted pairs (more twists per linear foot) and supports 1 Gbps for up to 100 meters or 10 Gbps for up to 55 meters.
  14. 14Cat6ean improvement of the Cat6 standard, supporting the same standards and lengths (with the ability to run 10 Gbps over 100 meters maximum), but using a higher quality cable that is more resistant to interference. This is most commonly used in wired networks today.
  15. 15What are RJ11 and RJ45 connectors used for in UTP cables?RJ11 connectors support two pairs of wires and are typically used in telephones. RJ45 connectors support four pairs of wires and are typically used with Ethernet cables.
  16. 16Coaxial Cableanalog cables made of copper but specifically engineered with a metal shield intended to block signal interference. Today, coaxial cables are mostly used by cable TV companies to connect their customers to the company’s facilities.
  17. 17What are fiber-optic cables and how do they transfer data?Fiber-optic cables use glass or plastic threads to transfer data using light (lasers or LEDs), allowing high bandwidth and digital data transfer with virtually no interference.
  18. 18What are the advantages of fiber cables over traditional metal cables?Fiber cables can carry more data at higher speeds, have no interference issues, are lighter and thinner, but are more expensive than metal cables.
  19. 19What is the difference between single-mode and multimode fiber cables?Single-mode cables use one fiber for high bandwidth over long distances with higher cost electronics. Multimode cables use wider fibers for effective medium distance transmission and are less expensive.
  20. 20What are the primary connector types for fiber cables and their uses?ST connectors were common for multimode fiber but are now often replaced by LC connectors, which are smaller and support more ports, commonly used in corporate data centers with SFP transceivers.
  21. 21Crossover cablesused to connect two computing devices of the same type directly to each other. this is accomplished via their network interface controllers (NIC) or switches
  22. 22Patch cablesused to connect a device to a wall outlet, for example. The wall outlet is wired to another patch panel in the networking closet, and that networking panel is wired into a switch. These cables can also be used to wire servers in a rack to the top-of-rack (ToR) switch.

Information

Description
GRE NetSec Foundations Flashcards on Network Media, Devices, and Standards, created by Joseph Rubino on 03/03/2024.
Created by
Joseph Rubino
Views
1
Rating

More on Network Cables and Physical Media

Feedback

What is it about?

What do you think of the new look?

How do you like it?