GoConqr has a new look! Let us know what you think.

Sign up free

Quiz

DIKTA ICND 1 Ch 6

Brian Gamble 9 questions

Take the quiz

Questions in this quiz (9)

  1. 1Which of the following statements describes part of the process of how a switch decides to forward a frame destined for a known unicast MAC address?
    1. AIt compares the unicast destination address to the bridging, or MAC address, table.
    2. BIt compares the unicast source address to the bridging, or MAC address, table.
    3. CIt forwards the frame out all interfaces in the same VLAN except for the incoming interface.
    4. DIt compares the destination IP address to the destination MAC address.
    5. EIt compares the frame’s incoming interface to the source MAC entry in the MAC address table.
  2. 2Which of the following statements describes part of the process of how a LAN switch decides to forward a frame destined for a broadcast MAC address?
    1. AIt compares the unicast destination address to the bridging, or MAC address, table.
    2. BIt compares the unicast source address to the bridging, or MAC address, table.
    3. CIt forwards the frame out all interfaces in the same VLAN except for the incoming interface.
    4. DIt compares the destination IP address to the destination MAC address.
    5. EIt compares the frame’s incoming interface to the source MAC entry in the MAC address table.
  3. 3Which of the following statements best describes what a switch does with a frame destined for an unknown unicast address?
    1. AIt forwards out all interfaces in the same VLAN except for the incoming interface.
    2. BIt forwards the frame out the one interface identified by the matching entry in the MAC address table.
    3. CIt compares the destination IP address to the destination MAC address.
    4. DIt compares the frame’s incoming interface to the source MAC entry in the MAC address table.
  4. 4Which of the following comparisons does a switch make when deciding whether a new MAC address should be added to its MAC address table?
    1. AIt compares the unicast destination address to the bridging, or MAC address, table.
    2. BIt compares the unicast source address to the bridging, or MAC address, table.
    3. CIt compares the VLAN ID to the bridging, or MAC address, table.
    4. DIt compares the destination IP address’s ARP cache entry to the bridging, or MAC address, table.
  5. 5PC1, with MAC address 1111.1111.1111, is connected to Switch SW1’s Fa0/1 interface. PC2, with MAC address 2222.2222.2222, is connected to SW1’s Fa0/2 interface. PC3, with MAC address 3333.3333.3333, connects to SW1’s Fa0/3 interface. The switch begins with no dynamically learned MAC addresses, followed by PC1 sending a frame with a destination address of 2222.2222.2222. If the next frame to reach the switch is a frame sent by PC3, destined for PC2’s MAC address of 2222.2222.2222, which of the following are true? (Choose two answers.)
    1. AThe switch forwards the frame out interface Fa0/1.
    2. BThe switch forwards the frame out interface Fa0/2.
    3. CThe switch forwards the frame out interface Fa0/3.
    4. DThe switch discards (filters) the frame.
  6. 6Which of the following devices would be in the same collision domain as PC1?
    1. APC2, which is separated from PC1 by an Ethernet hub
    2. BPC3, which is separated from PC1 by a transparent bridge
    3. CPC4, which is separated from PC1 by an Ethernet switch
    4. DPC5, which is separated from PC1 by a router
  7. 7Which of the following devices would be in the same broadcast domain as PC1? (Choose three answers.)
    1. APC2, which is separated from PC1 by an Ethernet hub
    2. BPC3, which is separated from PC1 by a transparent bridge
    3. CPC4, which is separated from PC1 by an Ethernet switch
    4. DPC5, which is separated from PC1 by a router
  8. 8Which of the following Ethernet standards support a maximum cable length of longer than 100 meters? (Choose two answers.)
    1. A100BASE-T
    2. B1000BASE-LX
    3. C1000BASE-T
    4. D100BASE-FX
  9. 9A Cisco LAN switch connects to three PCs (PC1, PC2, and PC3), each directly using a cable that supports Ethernet UTP speeds up through 1000 Mbps (1 Gbps). PC1 uses a NIC that supports only 10BASE-T, while PC2 has a 10/100 NIC, and PC3 has a 10/100/1000 NIC. Assuming that the PCs and switch use IEEE autonegotiation, which PCs will use half-duplex?
    1. APC1
    2. BPC2
    3. CPC3
    4. DNone of the PCs will use half-duplex.

Information

Description
Final / Review ICND 1 Quiz on DIKTA ICND 1 Ch 6, created by Brian Gamble on 24/02/2016.
Language
English
Views
35
Rating
No ratings yet
Rate this quiz
Rate this quiz

Feedback

What is it about?

What do you think of the new look?

How do you like it?