Quiz
CCNA 3v5.03 Chapter 7
This quiz has question types that open in the usual player.
Questions in this quiz (24)
1Refer to the exhibit. Which command should be used to configure EIGRP to only advertise the network that is attached to the gigabit Ethernet 0/1 interface?
- Anetwork 172.16.23.64 0.0.0.63
- Bnetwork 172.16.23.0 255.255.255.192
- Cnetwork 172.16.23.64 0.0.0.127
- Dnetwork 172.16.23.0 255.255.255.128
2What is the purpose of using protocol-dependent modules in EIGRP?
- Ato describe different routing processes
- Bto identify different application layer protocols
- Cto use different transport protocols for different packets
- Dto accommodate routing of different network layer protocols
3If all router Ethernet interfaces in an EIGRP network are configured with the default EIGRP timers, how long will a router wait by default to receive an EIGRP packet from its neighbor before declaring the neighbor unreachable?
- A10 seconds
- B15 seconds
- C20 seconds
- D30 seconds
4Which two EIGRP packet types are sent with unreliable delivery? (Choose two.)
- Aupdate
- Bquery
- Chello
- Dreply
- Eacknowledgment
5Which destination MAC address is used when a multicast EIGRP packet is encapsulated into an Ethernet frame?
- A01-00-5E-00-00-09
- B01-00-5E-00-00-10
- C01-00-5E-00-00-0A
- D01-00-5E-00-00-0B
6What is identified within the opcode of an EIGRP packet header?
- Athe EIGRP message type that is being sent or received from a neighbor
- Bthe EIGRP autonomous system metrics
- Cthe EIGRP hold timer agreed upon with a neighbor
- Dthe EIGRP sum of delays from source to destination
7Why would a network administrator use a wildcard mask in the network command when configuring a router to use EIGRP?
- Ato lower the router overhead
- Bto send a manual summarization
- Cto exclude some interfaces from the EIGRP process
- Dto subnet at the time of the configuration
8An administrator issues the router eigrp 100 command on a router. What is the number 100 used for?
- Aas the autonomous system number
- Bas the number of neighbors supported by this router
- Cas the length of time this router will wait to hear hello packets from a neighbor
- Das the maximum bandwidth of the fastest interface on the router
9What information does EIGRP maintain within the routing table?
- Aboth successors and feasible successors
- Bonly feasible successors
- Cadjacent neighbors
- Dall routes known to the router
- Eonly successors
10Which table is used by EIGRP to storre all routes that are learned from EIGRP?
- Athe routing table
- BThe neighbor table
- CThe topology table
- DThe adjacency table
11Which command or commands must be entered on a serial interface of a Cisco router to restore the bandwidth to the default value of that specific router interface?
- Abandwidth 1500
- Bshutdown
no shutdown - Ccopy running-config startup-config
reload - Dno bandwidth
12Which command is used to display the bandwidth of an interface on an EIGRP-enabled router?
- Ashow ip route
- Bshow interfaces
- Cshow ip protocols
- Dshow ip interface brief
13A new network administrator has been asked to verify the metrics that are used by EIGRP on a Cisco device. Which two EIGRP metrics are measured by using static values on a Cisco device? (Choose two.)
- Abandwidth
- Bload
- Creliability
- Ddelay
- EMTU
14Refer to the exhibit. Which two networks contain feasible successors? (Choose two.)
- A192.168.71.0
- B192.168.51.0
- C10.44.100.252
- D10.44.104.253
- E10.44.101.252
15Refer to the exhibit. R3 has two possible paths to the 172.16.99.0 network. What is the reported distance of the feasible successor route?
- A2340608
- B2169856
- C10512128
- D2816
16How do EIGRP routers establish and maintain neighbor relationships?
- Aby exchanging neighbor tables with directly attached routers
- Bby comparing known routes to information received in updates
- Cby exchanging hello packets with neighboring routers
- Dby dynamically learning new routes from neighbors
- Eby exchanging routing tables with directly attached routers
17What is indicated when an EIGRP route is in the passive state?
- AThe route has the highest path cost of all routes to that destination network.
- BThe route must be confirmed by neighboring routers before it is put in the active state.
- CThe route is a feasible successor and will be used if the active route fails.
- DThere is no activity on the route to that network.
- EThe route is viable and can be used to forward traffic.
18What is the multicast address used by an EIGRP-enabled router operating with IPv6?
- AFFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF
- BFF02::A
- CFF02::B
- DFF02::1
19Which configuration is necessary to ensure successful operation of EIGRP for IPv6?
- AThe eigrp router-id command requires an IPv6 address within the router configuration mode.
- BThe network command is required within the router configuration mode.
- CThe no shutdown command is required within the router configuration mode.
- DThe router eigrp autonomous-system command is required within the router configuration mode.
20Fill in the Blank. Use the abbreviation.
EIGRP uses the [blank_start]RTP[blank_end] protocol to deliver EIGRP packets to neighbors- ARTP
21Fill in the blank.
In an EIGRP topology table, a route that is in a/an [blank_start]active[blank_end] state will cause the Diffusing Update Algorithm to send EIGRP queries that ask other routers for a path to this network.- Aactive
22Match the correct version of EIGRP with the EIGRP features. (Not all options are used.)
- AEIGRP for IPv4 only
- Bboth EIGRP for IPv4 and IPv6
- CEIGRP for IPv6 only
23Order the precedence in which an EIGRP router would choose the router ID. (Not all options are used.)
- A_ first _
- B_ third _
- C_ second _
24Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.
Which code is displayed on the web server?- ADone
- BEIGRP
- CComplete
- DIPv6EIGRP
Information
- Description
- sophomore CCNA 3 Quiz on CCNA 3v5.03 Chapter 7, created by Christina Evans on 04/07/2016.
- Author
- Christina Evans
- Language
- English
- Views
- 41
- Tags
- Rating
- No ratings yet Rate this quiz