Quiz
CDC 2A652N - Volume 2 - Electrical and Electrical Circuits & Components
Create a free account to finish this quiz
Save your progress and see your final score.
Already have an account? Sign in
Questions in this quiz (60)
1Every atom must contain what types of particles?
- AElectrons and protons
- BElectrons and neutrons
- CProtons and neutrons
- DElectrons, protons and neutrons
2An atom with 8 electrons in its outermost shell is said to be
- AFree
- BStable
- CValence
- DIonized
3How many valence electrons are needed to make a good conductor?
- A3
- B4
- C5
- D6
4"Dielectric" is the term used for
- AConductors
- BInsulators
- CDoped atoms
- DSemi-conductors
5The flow or drift of electrons through a conductor” in the same direction at the same time is the definition of
- AConductivity
- BVoltage
- CCurrent
- DValence
6The potential difference between two points in a circuit that exerts a force on free electrons is called
- AConductivity
- BVoltage
- CCurrent
- DValence
7What is used to control current flow in a circuit?
- AVoltage
- BCoulombs
- CResistance
- DConductivity
8The relationship of voltage, current and resistance is expressed through
- AE, I and C
- BPower formulas
- CConductance
- DOhm's Law
9Total current in a series circuit is equal to the
- ACurrent through one component
- BSum of the current through each component
- CReciprocal of the current through one component
- DReciprocal of the sum of the currents through each component
10What is the wattage of a circuit with 28 volts applied and a total resistance of .2 ohms?
- A.14 watts (w)
- B.14 kilowatts (kW)
- C3.92 W
- D3.92 kW
11In a parallel circuit, the total voltage is equal to the
- ASum of the voltages across each branch
- BVoltage across each resistor
- CVoltage across each branch
- DThe reciprocal of the voltage across the resistances
- ASum of the voltages across each branch
12Source current in a parallel circuit will be divided according to branch
- AVoltage
- BPowers
- CLengths
- DResistances
13The area around a magnet where its influence can be felt is the definition of the
- ASaturation principle
- BMagnetic theory
- CMagnetic field
- DLaw of attraction and repulsion
14“The ability of a material to pass lines of force” is a definition of
- APermeability
- BReluctance
- CElectromagnetism
- DRetentively
15The magnetism that remains after the magnetizing force has been removed is known as
- AElectromagnetism
- BMolecular magnetism
- CPermeability
- DResidual magnetism
16The magnetic field of an electromagnet can be varied by changing the
- AType of core
- BNumber of turns in the coil
- CAmount of current through the coil
- DAll of the above
17The electromechanical generation of a voltage requires a magnetic field, relative motion, and
- AA complete circuit
- BA conductor
- CAn insulator
- DA load
18The principle behind all electromechanical generation is
- AConduction
- BCommutation
- CRectification
- DElectromagnetic induction
19The function of the commutator in a DC generator is to
- AComplete the circuit to the load
- BInduce DC into the external circuit
- CRectify the input
- DChange AC voltage to DC voltage
20Because an inductor stores energy and then returns it to the circuit, it is called a
- AResistive device
- BReactive device
- CRetentive device
- DRetroactive device
21An inductor stores energy in the form of
- AHeat
- BResistance
- CA magnetic field
- DAn electrostatic field
22The process by which a current change in one coil produces a voltage in another coil is called
- AInductance
- BSelf-induction
- CMutual induction
- DNone of the above
23A transformer will change all of the following except
- APower
- BCurrent
- CVoltage
- DResistance
24Normally, the winding of a transformer that is connected to a power source is known as the
- AField winding
- BPrimary winding
- CCurrent winding
- DSecondary winding
25What kind of turns of wire is found in the secondary windings of a step up transformer?
- AEqual
- BLess
- CMore
- DAll of the above
26A relay is an electrically operated
- AMeter
- BMotor
- CSwitch
- DSafety device
27A relay that, once energized, requires a second coil to be energized before the contacts will return to their original positions is called a
- ALocking relay
- BLatching relay
- CTiming relay
- DTripping relay
28A capacitor stores energy in the form of
- AHeat
- BResistance
- CA magnetic field
- DAn electrostatic field
29In a capacitor, the dielectric is the
- APositive lead
- BConductor
- CInsulator
- DOuter case
30Opposition of a capacitor to AC is called
- AInductive reactance
- BImpedance
- CCapactive reactance
- DCapacitance
31The factors which determine the time required to charge a capacitor are the capacitance and the
- AApplied voltage
- BCircuit current
- CAmount of resistance
- DType of dielectric
32The anode of a diode is constructed of
- ANeutral material
- BBiased material
- CPositive material
- DNegative material
33Expanding or contracting the depletion region of a diode is called
- ABasing
- BGating
- CSpiking
- DBiasing
34A diode placed in a circuit in reverse bias is being used as
- AA spike protector
- BAn amplifier
- CA regulator
- DA rectifier
35A zener will conduct in reverse bias
- AFor a second or two at a time
- BUntil gate potential has been reached
- COnce the avalanche point has been reached
- DUntil the breakdown point has been reached
36A zener being used as a regulator must have a resistor placed in the circuit in
- ASeries
- BParallel
- CReverse bias
- DSeries-parallel
37What is the approximate operating voltage of a LED?
- A.5 volts
- B.1 volt
- C1.6 volts
- D2.4 volts
38The SCR has how many PN junctions?
- A1
- B2
- C3
- D4
39The amount of current required to gate an SCR is called
- AForward break over voltage
- BHolding current
- CPeak voltage
- DGate current
40In order for an SCR to be turned off
- AThe forward break over voltage must exceed the holding voltage.
- BThe current must drop below the holding current.
- CThe negative amp switch must activate.
- DThe negative volt switch must activate.
41The best method of troubleshooting is the
- ASystematic method
- BInstantaneous method
- CHit-and-miss method
- DTrial-and-error method
42Which troubleshooting step is done by knowing proper equipment operation?
- AAnalysis
- BRecognition
- CRepair and check
- DElimination and isolation
43During which troubleshooting step do you try to determine which system could cause the malfunction?
- AAnalysis
- BVerification
- CRecognition
- DElimination and isolation
44During which troubleshooting step do you first use the schematic diagram?
- ARecognition
- BVerification
- CAnalysis
- DIsolation
45Which troubleshooting aid is designed to aid you if you see an unfamiliar symbol?
- AZones
- BSchematic
- CWiring diagram
- DReference designation index
46Which troubleshooting aid is designed to aid you in finding components on a diagram?
- AZones
- BSchematic
- CWiring diagram
- DReference designation index
47When used in a series circuit to measure voltage, how is a multimeter connected in the circuit?
- AIn series
- BTo ground
- CIn parallel
- DIn series-parallel
48To set a value to the height of the oscilloscope grid markings, you adjust the
- AFocus
- BPitch control
- CVoltage selector
- DTime sweep selector
49To ensure accuracy of an oscilloscope when preparing for operation you should always,
- AZero the display
- BCenter the display
- CIdentify the cal point and adjust to zero
- DIdentify the cal point and calibrate the display
50When you are testing a transformer, an open coil reading on the 8025A multimeter will be indicated by
- AA beep
- BAn extending analog bar graph
- COL
- D0 ohms
51Which could be the indication from the 8025A multimeter when you are checking a serviceable capacitor?
- AA beep
- BAn extending analog bar graph
- COL
- D0 ohms
52How many junctions are checked to test the serviceability of a transistor?
- A1
- B2
- C3
- D4
53When checking a FET, you must check the diode junction and the continuity between the
- AGate and source
- BSource and drain
- CGate and substrate
- DSubstrate and drain
54How can you identify an electrostatic sensitive device?
- AThe package will have special coloring as specified in local directives.
- BThe package will have a special control number as specified in local directives.
- CIt will be marked with the MIL-STD–129 symbol or a caution marking.
- DIt will be marked with the MIL-SPC–235 symbol or a warning marking.
55A heat sink is used in soldering to
- APrevent heat from damaging the component being soldered
- BPrevent heat from damaging other components in the circuit
- CApply heat to the component being soldered
- DApply heat to other components in the circuit
56A pitted or worn soldering iron tip should be redressed with a flat, fine, single-cut file and should be
- ATinned
- BClean of solder
- CReplaced
- DChecked for length
57The first step in soldering a conductor is to
- AWick the wire
- BRemove the insulation
- CApply heat to the connection
- DApply solder to the connection
58When soldering flat perforated terminals, the conductor is connected to the terminal using
- A90 degree wrap
- B180 degree wrap
- C270 degree wrap
- D360 degree wrap
59A wire is inserted into a solder cup until the
- AWire touches the bottom
- BWire clears the top of the cup
- CInsulation touches the cup
- DWire protrudes from the weep hole
60The best method of repairing a lifted circuit track on a PCB is to
- ABond it
- BGlue it
- CReplace it with bare wire
- DReplace it with insulated wire
Information
- Description
- CDC 2A652N - Volume 2 - Electrical and Electrical Circuits & Components
- Author
- nicilynn1981
- Language
- English
- Views
- 137
- Tags
- Rating
- 4.0 out of 5 · 1 rating Rate this quiz