Flashcards
L#19 Plastics and Composites
Cards in this deck (22)
- 1Which metal manufacturing process is processing of plastics and elastomers similar to? (1)Similar to forming and shaping of metals (1)
- 2What categorizes the two types of plastics (2)1. THERMOPLASTICS: Melt at low temperature
2. THERMOSETS: Cure at low temperature - 3Why is the low melting and curing of plastics an advantage over metals? (2)1. Because of this low energy requirement, plastics are easy to handle and require less force and energy to process compared to metals.
2. Plastics can be moulded, cast, formed and machined with ease and at high production rates - 4With use of relevant diagrams, explain plastic extrusion (10)1. In Extrusion, which produces the largest volume of plastics, raw materials in the form of thermoplastic pellets, granules, or powder are placed into a hopper and fed into the barrel of a screw extruder
2. See notes for diagram of screw extruder
3. The molten plastic is forced through a die in a process similar to that of extruding metals
4. A metal-wire filter screen usually is placed just before the die to filter out unmelted or congealed resin
5. This screen also helps build up back pressure in the barrel and is replaced periodically
6. The barrel is externally heated to promote melting
7. There are several variations on the basic extrusion process for producing a number of different products
8. For example, plastic tubes and pipes are produced in a spider die
9. The produced tubes can then be used to make plastic bags and other thin polymer film products using a blowing process
10. See notes for spider die and blow film process diagrams - 5Which metal manufacturing process is injection moulding similar to? (1)1. Hot-chamber die casting
- 6Describe simply how injection moulding works (2)1. Plastic pellets or granules are fed into the heated cylinder, and the melt is forced into the mould either by a hydraulic plunger or by the rotating screw system of an extruder
2. As in plastic extrusion, the barrel (cylinder) is heated externally to promote melting of the polymer - 7What provides a much greater proportion of heat generated in injection moulding compared to plastic extrusion? (1)1. Frictional heating
- 8Draw annotated diagrams of injection moulding with a : 1) plunger ii) Reciprocating screwSee notes (2)
- 9Which of the two injection moulding types to most modern machine use? (1)Reciprocating screw type (1)
- 10Describe the three operation sequence for the reciprocating screw injection moulding process (3) and draw drawings for each1. Build up polymer in front of sprue bushing; pressure pushes in the screw backwards. When sufficient polymer has built up, rotation stops.
2. When the mold is ready, the screw is pushed forward by a hydraulic cylinder, filling the sprue bushing, sprue, and mold cavity with polymer. The screw begins rotating again to build up more polymer.
3. After polymer is solidified/cured, the mould opens, and ejector pins remove the molded part - 11Describe in further detail the reciprocating screw injection moulding process (4)1. As the pressure builds up at the mould entrance, the rotating screw begins to move backwards under pressure to a pre-determined distance
2. This movement controls the volume of material to be injected
3. The screw then stops rotating and is pushed forward hydraulically, forcing the molten plastic into the mould cavity
4. The pressures developed are usually range from 70 to 200 MPa - 12In injection moulding, At what temperature are thermplastic moulds usually kept at? (1)1. 90 degrees celsius
- 13In injection moulding, at what temperature are thermoset parts usually moulded at?200 degrees celsius (1)
- 14What takes plce in thermosetting? (2)Polymerisation (1) and cross-linking (1)
- 15Draw annotated diagrams of the three injection moulding mould types (3)See notes (3)
- 16What are the three categories of moulds for injection moulding (3)1. Cold-runner two plate mould
2. Cold-runner three-plate mould
3. Hot runner mould - 17What is the difference between cold-runner and hot-runner mould processes? (2)1. Cold runner molds: The solidified plastic remaining in the channels connecting the mould cavities to the end of the barrel and must be removed later
2. Hot-runner moulds: There are no gates, runners or sprues attached to the moulded parts (these are more expensive) - 18Describe and illustrate the rotational moulding process (5)1. Most thermosplastics and some thermosets can be formed into large, hollow parts by rotational moulding
2. In this process, thin-walled metal mould is made in two pieces (split-female mould) and is designed to be rotated about two perpendicular axes.
3. For each part cycle, a pre-measured quantity of powderd plastic is placed inside the warm mould.
4. Then the mould is heated (usually in a large oven) and is rotated continuously about the two principal axes
5. See notes for diagrams - 19Describe and illustrate the blow/compression moulding process (9)1. Blow moulding is a modified extrusion and injection moulding process
2. In extrusion blow moulding, a tube or preform is first extruded
3. It is then clamped into a mould with a cavity much larger than the tube diameter and blown outward to fill the mould cavity.
4. The blow ratio maybe as high as 7:1 and the blowing is usually done with a hot blast with a pressure ranging from 350 to 700 kPa
5. See notes for diagrams
6. In compression moulding, the plastic (in the form of pre-shaped material or a viscous mixture of liquid resin and filler) is placed directly in a mould cavity.
7. Forming is done from a plug or from the uppe rhalf of the die.
8. The process is thus similar to closed-die forging
9.See notes for diagram - 20Summarize plastic casting (4)1. Some thermoplastics (such as nylons and acrylics) and thermosetting plastics (epoxies, phenolics, polyurethanes, and polyester) can be cast into a variety of shapes using either rigif or flexible moulds
2. Compared with other methods of processing plastics, casting is a slow, but simple and inexpensive, proess
3. However, the polymer must have sufficiently low viscosity in order to flow easily into the mould
4. Typical parts cast are gears (especially ylon), bearings, wheels, thick sheets, lenses, and components requiring resistance to abrasive wear - 21Summarize, with use of a diagram, filament moulding (9)1. A process in which the resin and fibres are combined at the time of curing in order to develop a composite structure
2. Axisymmetric parts (such as pipes and storage tanks), and even non-symmetric parts, are produced on a rotating mandrel
3. The reinforcing filament, taoe, or roving is wrapped continuously arround the form
4. The reinforcements are impregnated by passing them through a polymer bath
5. This process can be modified by wrapping the mandrel with a pre-preg material
6. The products made by filament winding are very strong because of their highly reinforced structure
7. Parts as large as 4.5 m in diameter and 20 m long have been made by this process
8. Filament winding also has been used for strengthening cylindrical or spherical pressure vessels made of materials such as aluminium and titanium, where the presence of a metal inner liner makes th e part impermeable
9. See notes for diagram - 22Summarize, with use of a diagram, the spray layup and hand layup (contact moulding) process (8)1. These are a series of processes where a single moulld us used and is thus also referred to as open-mould processing
2. The simplest method of contact moulding is hand layup
3. The materials are placed in proper order (resins and reinforcements), brushed and shaped in the mould be hand with a roller
4. The squeezing action of the roller expels trapped air bubbles and compacts the part
5. In spray layup, moulding is done by spraying the materials into the mould.
6. Both the resin and the chopped fibres are sprayed over the mould surfaces
7. Rolling the deposited materials may be necessary in the process
8. See notes for diagrams for hand layup and spray layup
Information
- Description
- Manufacturing Operations and Technology Flashcards on L#19 Plastics and Composites, created by Block on 05/05/2014.
- Created by
- Block · May 2014
- Updated
- Apr 6, 2018
- Views
- 16
- Rating