Help shape GoConqr. What should we add next?

Notes

shape and space 2

shania catania maths form 3 English 1 page

Content of the notes (1)

Page 1

Special Quadrilaterals

Bookmark this page

A general quad

lateral has four sides and the sum of its interior angles is 360; unless told

otherwise, no sides are equal and no angles are equal. However there are

several special cases.

SQUARE

In a

square, all four sides are equal and all four angles are right angles. A square

has four lines of symmetry.

RECTANGLE

In a

rectangle, the opposite sides are equal and all four angles are right angles. A

rectangle has two lines of symmetry.

PARALLELOGRAM

A

parallelogram has opposite sides that are equal and parallel, and opposite

angles that are equal. A parallelogram has no lines of symmetry but it does

have rotational symmetry of order 2.

RHOMBUS

In a rhombus the opposite angles

are equal, the opposite sides are parallel and all four sides are the same

length. A rhombus has two lines of syuunetiy (the diagonals).

KITE

A kite

has one pair of opposite angles equal and two pairs of adjacent sides equal. A

kite has one line of symmetry. It has no rotational symmetry.

TRAPEZIUM

A

trapezium has one pair of opposite sides parallel. Usually it has no line of

symmetry.

However,

in the special case when the two sloping sides are the same length there is

oneline of symmetry. This is called an isosceles trapezium. Its non-parallel

sides are e4ual andtwo pairs of adjacent angles are equal.

Transformations

A translation occurs when a shape has been moved from one place to

another. It is equivalent of picking up the shape and putting it down

somewhere else. Vectors are used to describe such

transformations.

When describing a reflection, you need to state the line which the

shape has been reflected in.

When describing a rotation, the centre and angle of rotation are

given. If you wish to use tracing paper to help with rotations: draw the

shape you wish to rotate onto the tracing paper and put this over shape.

Push the end of your pencil down onto the tracing paper, where the centre

of rotation is and turn the tracing paper through the appropriate angle.

The resultant position of the shape on the tracing paper is where the shape

is rotated to.

Enlargements

Enlargements have a centre of enlargement and a scale factor.

1) Draw a line from the centre of enlargement to each vertex ('corner') of

the shape you wish to enlarge. Measure the lengths of each of these lines.

2) If the scale factor is 2, draw a line from the centre of enlargement,

through each vertex, which is twice as long as the length you measured. If

the scale factor is 3, draw lines which are three times as long. If the

scale factor is 1/2, draw lines which are 1/2 as long.

Example:

The centre of enlargement is marked. Enlarge the triangle by a scale factor

of 2.

Vectors

A vector quantity has both length (magnitude) and direction. The opposite

is a scalar quantity, which only has magnitude. Vectors can be denoted by AB,

a, or AB (with an arrow above the letters).

If a = (3) then the vector will look as follows:

(2)

NB1: When writing vectors as one number above another in

brackets, this is known as a column vector.

NB2: in textbooks and here, vectors are indicated by bold type. However,

when you write them, you need to put a line underneath the vector to

indicate it.

Multiplication by a Scalar

When multiplying a vector by a scalar (i.e. a number), multiply each

component of the vector by the scalar.

Example:

If a = ( 3 ), and b = 2a, sketch a and b.

( 2 )

If a = ( 3 ), 2a = ( 6 )

( 2 )

( 4 )

Vector Manipulation

Example:

If a = (-5) and b = ( 2), find the magnitude of their

resultant.

( 3)

( 1)

The resultant of two or more vectors is their sum.

The resultant therefore is (-3).

( 4)

The magnitude of this is Ö(-3² +

4²) = Ö(9 + 16) = Ö(25) = 5

The addition and subtraction of vectors can be shown diagrammatically. To

find a + b, draw a and then draw b at the end

of a. The resultant is the line between the start of a and

the end of b.

To find a - b, find -b (see above) and add this to a.

Example:

Unit Vectors

A unit vector has a magnitude of 1. The unit vector in the direction of the

x-axis is i and the unit vector in the direction of the y-axis is j.

For example on a graph, 3i + 4j would be at (3 , 4). This

method is another method of writing down vectors.

Example: 3i + j plus 5i - 4j =

8i - 3j. This is equivalent to:

( 3) + ( 5 ) = ( 8 )

( 1 ) ( -4) ( -3)

special quadeilaterals

transformation

vectors

Information

Description
form 3 maths Note on shape and space 2, created by shania catania on 25/08/2013.
Created by
shania catania · Aug 2013
Updated
Feb 19, 2016
Views
110
Tags
maths
Rating

More on Quadrilaterals

Feedback

What is it about?

What should we add next?